Inkmachines nr. 41B - X2 Eccenter assy (Preset LONG 4.5MM) - 1pcs

Inkmachines nr. 41B - X2 Eccenter assy (Preset LONG 4.5MM) Fits all Dragonfly machines. Pre-set to Long stroke 4.5mm Can also be adjusted with the No.90 Precision tool kit From 2.6 - 4.5mm Note that you will also need the No. 55 - Circlip pliers to replace this assembly. Hint! Use the Circlip Pliers to remove the Circlip and push out the Connecting pin. Loosen the excenter from the motor shaft with the smallest allen key 0.9mm. There are two screws on the standard excenter, one for the motor shaft and one for the bearing shaft. You only need to use the one for the motor shaft. Install the new assembly on the motor shaft and make sure that the screw ends up on the flat part of the shaft and tighten it securely. Check that the Connecting rod aligns properly with the groove in the Piston. This is important, if it does not align correctly it will not run properly and you might have to readjust the location of the motor. In that case please refer to the manual or send for service. If ok align the upper bearing with the hole in the piston and insert the Connecting pin and install the Circlip. X2 Eccentric assembly with preset LONG stroke of 4.5mm for InkMachines Dragonfly X2 tattoo machine, original spare part no. 41B, 1 piece. The LONG variant with 4.5mm stroke is designed for tattoo styles requiring deep and powerful penetration: intensive color packing, dense fills, traditional bold, neo-traditional, and any work requiring maximum ink saturation in the skin. The long 4.5mm stroke allows the needle to penetrate deeper and cover more area with each stroke, reducing the number of passes needed and accelerating the filling process. Manufactured with the same legendary precision as all InkMachines components, the LONG eccentric assembly transforms the Dragonfly X2 into a workhorse capable of delivering dense and consistent fills. Combined with adequate speed and correct tension settings, the LONG eccentric enables complete color saturation even on more resistant skin types. InkMachines offers three stroke variants (2.6mm, 3.7mm, 4.5mm), and the ability to change them transforms a single machine into three different instruments. Original InkMachines part priced at approximately 38 EUR, with guaranteed and precisely calibrated 4.5mm stroke. The power and consistency of the LONG stroke transforms the Dragonfly X2 into a formidable filling machine capable of delivering superior color saturation in shorter sessions. The LONG eccentric is available on tatuat.ro with fast delivery in Romania and Swedish InkMachines manufacturer guarantee. This eccentric variant is the workhorse choice for artists who specialize in bold color work and need maximum ink saturation capability. Frequently Asked Questions What is the LONG 4.5mm stroke ideal for? The LONG 4.5mm stroke is ideal for: intensive color packing, dense and uniform fills, traditional bold style, neo-traditional, work on areas with resistant skin, and any technique requiring deep penetration and maximum ink saturation. It is the preferred eccentric for intensive filling sessions. Is the 4.5mm stroke too long for lines? Yes, the 4.5mm stroke is not recommended for fine lines as deeper penetration can cause blow-outs and blurry lines. For lining, the SHORT 2.6mm or STANDARD 3.7mm eccentric are much more suitable. Each eccentric has its optimal use domain. Does the LONG stroke produce more noise? The longer stroke produces slightly more noise and vibration than the short stroke, as the movement amplitude is larger. The difference is minimal due to InkMachines precision design but can be perceptible. All variants are designed for quiet operation within the context of their performance. Can I use the LONG stroke for delicate shading? The LONG stroke can be used for shading but requires more control and experience to achieve delicate gradients. Speed and technique must be adapted to compensate for deeper penetration. For delicate shading, the STANDARD 3.7mm eccentric is usually a safer choice. How much does the LONG 4.5mm eccentric cost? The X2 eccentric assembly LONG 4.5mm InkMachines no. 41B is available at approximately 38 EUR, the same price as SHORT and STANDARD variants. The investment transforms the Dragonfly X2 into a powerful filling machine without purchasing separate equipment. How do I change the eccentric from STANDARD to LONG? The change involves partial disassembly of the Dragonfly X2 machine to access the eccentric compartment, removing the STANDARD assembly and installing the LONG one. The process takes 15-30 minutes. Consult the InkMachines guide for detailed step-by-step instructions. Does the LONG eccentric wear the machine faster? The longer stroke generates slightly larger forces in the drive mechanism, which theoretically can marginally accelerate wear. In practice, the difference is insignificant due to material quality and the robust Dragonfly X2 design. Regular maintenance is more important than the eccentric variant used. What power supply voltage do you recommend for the LONG stroke? The LONG stroke usually requires slightly higher voltage than the SHORT stroke to compensate for increased resistance and maintain optimal performance. The exact setting depends on cartridge type, work style, and personal preferences. Start at medium voltage and progressively adjust based on results. Is the LONG eccentric the most popular? Popularity varies depending on artists' predominant style. The STANDARD 3.7mm eccentric is the most versatile and popular for general use. LONG 4.5mm is preferred by artists specializing in traditional, neo-traditional, and intensive color work. SHORT 2.6mm is the favorite of artists specializing in finesse. Can I order a complete set of eccentrics? Yes, you can purchase all three eccentric variants (SHORT 2.6mm, STANDARD 3.7mm, and LONG 4.5mm) individually from tatuat.ro. Having the complete set gives you total versatility, allowing you to adapt the Dragonfly X2 machine to any tattoo style and any client requirement.