Complete guide: Ultrasonic sterilizer
It is a professional deep-cleaning device for tattoo and micropigmentation instruments, using 40.000 Hz ultrasonic waves that generate microbubbles in the liquid (cavitation) to remove dried ink, blood, and biofilm from the hardest-to-reach areas. The stainless steel tank has a capacity of 600 ml, and the digital timer with LED display allows you to set the cycle duration. It is the right equipment for any studio that reuses metal instruments and wants proper cleaning before autoclaving. Keep in mind from the start: this is the PRE-sterilization step, it does not replace the autoclave.
How to use
- Place the device on a flat, stable surface and plug it into the mains (220-240V). The non-slip feet help with stability.
- Fill the tank (600 ml capacity) with distilled or deionized water together with a special ultrasonic cleaning solution. Avoid tap water, which leaves mineral deposits.
- Place the instruments in the tank, preferably disassembled and with joints open, so that they are completely covered by the liquid.
- Put the lid on, set the desired time (the timer allows values from 3 to 59 minutes; a typical cycle is between 3 and 15 minutes, depending on the level of dirt) and start the cycle.
- At the end of the cycle, remove the instruments and rinse them with clean water to remove the cleaning solution.
- Dry the instruments completely before the next step.
- Proceed with sterilization in the autoclave, according to standard hygiene protocol. Ultrasonic cleaning is only the first link in the chain: ultrasonic cleaning, rinsing, drying, autoclaving.
- After use, empty the tank and wipe it; do not leave contaminated liquid in the device.
Tips from us
- Use distilled or deionized water plus a dedicated ultrasonic solution, not tap water and not regular detergent.
- Disassemble parts with joints or connections before cleaning, so that the microbubbles reach all cavities.
- For very dirty instruments, run two successive cycles instead of excessively extending a single one.
- Change the liquid after each work session or as soon as it becomes visibly dirty; contaminated liquid reduces efficiency and can re-contaminate the instruments.
- Never start the device with an empty tank and do not exceed the maximum fill level.
- Place the instruments so that they are covered by the liquid and, ideally, not stuck to the bottom of the tank.
Warning: It is an electrical device: do not submerge it, do not operate the panel with wet hands, and do not put your hand in the liquid while it is running. Do not use flammable solvents in the tank. Most important for client safety: ultrasonic cleaning is a PRE-sterilization step, it does NOT replace autoclaving. Instruments must be rinsed, dried, and then sterilized in an autoclave before reuse, according to sanitary regulations. Use the device only on instruments compatible with ultrasonic cleaning.
Frequently asked questions
Does it replace the autoclave?▾
No. Ultrasonic cleaning is the pre-sterilization step: it removes dirt and contaminants from hard-to-reach places. After this step, the instruments must be rinsed, dried, and sterilized in an autoclave, according to standard hygiene protocols.
What cleaning liquid should I use?▾
Distilled or deionized water together with a special ultrasonic cleaning solution is recommended. Do not use tap water, as it can leave mineral deposits on the instruments and in the tank.
What instruments can I clean with it?▾
Metal instruments that are reused in the studio, such as metal grips, tubes, tweezers, and scissors. Place them disassembled and completely covered by the liquid for the best result. For any delicate parts or parts made of other materials, first check if the manufacturer recommends them for ultrasonic cleaning.
How long does a cleaning cycle take?▾
The timer allows setting between 3 and 59 minutes, and the default value is approximately 3 minutes. A typical cycle lasts between 3 and 15 minutes, depending on how dirty the instruments are; for heavy dirt, you can run successive cycles.
How often should the liquid be changed?▾
Change the liquid after each work session or whenever it becomes visibly dirty. Contaminated liquid reduces cleaning efficiency and can re-contaminate already processed instruments.
Can it damage or scratch the instruments?▾
Ultrasonic cleaning is a non-abrasive method: it does not scratch, bend, or damage metal instruments, because it works through microbubbles in the liquid, not through mechanical friction.
Product description
Ultrasonic sterilizer Ultrasonic frequency: 40,000Hz Liner material: stainless steel SUS303Capacity: 600 ml Time Control: 3-minute Auto Cut-off Power supply: AC 220 ~ 240V, 50 / 60 Hz Power: 35WPackage Dimensions: 265 x 170 x 185 mm ( L x W x H )Inner tank size: 155 x 95 x 52 mm ( L x W x H )Dimensions: 200 x 140 x 125 mm (L x W x H)Features: The ultrasonic power conversion efficiency is high and the cleaning speed is fast, which is several times to dozens of times higher than the traditional cleaning method. Good cleaning effect and high cleanliness, and can effectively clean deep holes, fine seams and hidden places of irregular workpieces. Ultrasonic cleaning can kill bacteria, dissolve organic pollutants, and prevent over-corrosion. Classic and practical design saves solvent, heat, workplace and labor when cleaning workpieces. The pursuit of perfection and humanization of products, digital control, LED digital display. The time can be freely set from 3-59 minutes, the time of the cleaning process is counted down, and the default working time is 180 seconds. The cleaning tank is made of high-quality SUS304 stainless steel by one-time stamping, without welding, and has good waterproof performance. The cleaning basket is made of injection molding, which is beautiful and elegant. Using high-quality imported core components, moisture-proof PCB board processing, long service life. When cleaning objects, it is not necessary to touch the cleaning liquid by hand, and there is no need to stir the workpiece, which is safe and reliable without damage to the surface of the workpiece.
The ultrasonic sterilizer is indispensable professional equipment for deep cleaning tattoo and micropigmentation instruments before the autoclaving process. Ultrasonic technology generates millions of microscopic bubbles through acoustic cavitation that implode on contact with instrument surfaces, efficiently removing ink residue, dried blood, biofilm, and other contaminants from the most hard-to-reach areas such as cavities, joints, and grooves. This cleaning method is superior to manual washing because it reaches places impossible to clean through conventional methods. The corrosion-resistant stainless steel tank offers generous capacity for simultaneous processing of multiple instruments. The digital timer allows precise cleaning cycle duration setting, generally between 3 and 15 minutes depending on contamination level. Operation is quiet and energy efficient, and the process does not damage or scratch delicate instruments. The ultrasonic sterilizer is a critical step in the professional sterilization chain: ultrasonic cleaning, followed by rinsing, drying, and autoclaving. Investment in this equipment demonstrates compliance with the strictest hygiene protocols and patient protection according to European sanitary standards. The exterior body is ergonomically designed with accessible control panels and clear visual operating status indicators. The transparent lid allows monitoring the cleaning process without interruption. Non-slip feet ensure stability on any work surface, and the modern design aesthetically integrates into any professional tattoo studio.
Frequently Asked Questions How does ultrasonic cleaning work? Ultrasonic waves create millions of microscopic bubbles in the cleaning liquid through cavitation. These bubbles implode on contact with instrument surfaces, dislodging and removing contaminants from the smallest spaces. What cleaning liquid should be used? Distilled or deionized water combined with a special ultrasonic cleaning solution is recommended. Do not use tap water, which can leave mineral deposits. Does it replace the autoclave? No, ultrasonic cleaning is the PRE-sterilization step. After ultrasonic cleaning, instruments must be rinsed, dried, and sterilized in an autoclave per standard hygiene protocols. How long does a cleaning cycle take? A typical cycle takes between 3 and 15 minutes, depending on instrument contamination level. For heavily soiled instruments, successive cycles can be run. Can it damage instruments? No, ultrasonic cleaning is a non-abrasive method that does not scratch, bend, or damage metal instruments. It's safe for grips, tweezers, tubes, and other components. How often should the liquid be changed? The liquid should be changed after each work session or when it becomes visibly dirty. Using contaminated liquid reduces cleaning efficiency and can re-contaminate instruments. Is it noisy? Modern ultrasonic sterilizers are relatively quiet, producing a slight buzzing during operation. The noise level is acceptable for studio use. What instruments can be cleaned? Metal grips, tubes, tweezers, scissors, micropigmentation instruments, and any other reusable metal components can be cleaned. Do not insert soft plastic objects. How much water fits in the tank? Capacity varies by model, usually between 500ml and 2 liters for models designed for tattoo studios. Check specifications for exact capacity. Is it necessary for every tattoo studio? Yes, ultrasonic cleaning is a recommended step in the professional sterilization protocol. It's considered best practice in the tattoo industry for ensuring complete hygiene.
