Complete guide: Inkmachines track nr. 22-O-ring noise mitigation - 2pcs
This is an original Ink Machines spare part — a set of two damping O-rings (No. 22) that mount under the machine's inner piston and absorb mechanism vibrations, reducing noise during work. It is intended for artists who use Ink Machines rotary machines and do their own maintenance, or for those who want a quieter working environment during long sessions. The manufacturer's description indicates it for Dragonfly X2, and on tatuat.ro the part appears under components for the Inkmachines, Dragonfly, and Stingray lines.
How to use
- Turn off and disconnect the machine before any intervention and work on a clean surface, with washed hands or gloves.
- Remove the needle bar pin (the pin that secures the needle bar).
- Remove the cap and adjustment screw to access the inner piston.
- Carefully extract the inner piston and remove the old O-ring, which sits under the piston.
- Apply a little grease to the new O-ring before installation, so it slides easily into the slot.
- Place the O-ring flat in the hole and check that it is not twisted or pinched before reinserting the inner piston.
- Reassemble in reverse order: inner piston, adjustment screw, cap, and needle bar pin.
- Run the machine idle for a few seconds and check for quiet operation before starting a session.
Tips from us
- The set contains 2 pieces, so you can do a preventive replacement and keep one as a spare in your kit.
- Replace the O-ring when you notice increased noise levels, visible deformation, or hardening/loss of elasticity of the material — these are the classic signs of wear.
- Use only a little machine-specific grease; excess attracts dust and lint into the mechanism.
- Make sure the ring sits perfectly flat in its slot before reassembly — a twisted O-ring does not dampen properly and can become damaged.
- Prefer the original part, calibrated for the machine, instead of a generic O-ring with unknown hardness and dimensions.
Warning: Disconnect the machine before servicing and handle the parts without forcing them, to avoid damaging the thread or piston. The O-ring is an internal part — the tattoo machine is not sterilized in an autoclave, but is protected during work with a barrier (disposable film/sleeve) and disinfected on the surface between clients. Elastomers degrade faster with repeated heat, so avoid unnecessary exposure to high temperatures and check the rings' condition visually at each maintenance.
Frequently asked questions
Which machines is this O-ring for?▾
It is the original Ink Machines part No. 22 for noise damping. The manufacturer's description indicates it for Dragonfly X2, and on tatuat.ro it is listed under parts for the Inkmachines, Dragonfly, and Stingray lines. Before ordering, check the part number (No. 22) in your machine's diagram to make sure it is the correct component.
How many pieces does the set contain?▾
The set contains 2 O-rings, enough for a complete overhaul and to keep one as a spare.
How do I know when it needs to be replaced?▾
The typical signs are increased machine noise level, visible deformation of the ring, and hardening or loss of elasticity of the material. Being a wear part, it gradually loses its damping properties, so it should be checked periodically during maintenance.
Can I use a generic O-ring instead of the original?▾
It is not recommended. The hardness and dimensions are calibrated for the machine's mechanism; a ring that is too soft wears out quickly, and one that is too hard does not absorb vibrations effectively. The original part gives you the damping designed by the manufacturer and the correct fit in the slot.
How do I properly maintain the machine and O-ring?▾
Protect the machine during work with a disposable barrier and disinfect it on the surface between clients — do not put the machine in an autoclave. When installing the O-ring, use a little machine grease, work with clean hands or gloves, and periodically check the rings' condition during maintenance, replacing them at the first signs of wear.
Is it an original part?▾
Yes, it is an original Ink Machines spare part (Swedish manufacturer), identified by reference number 22 and model 375570.
Product description
Inkmachines track nr. 22-O-ring noise mitigation Hint! The Noise damper O-ring is located under the inner piston to work against noise. To replace it you need to take out the needlebar pin, remove the cap and the adjustment screw. Put some grease on the new O-ring before installing it and make sure it lies flat in the hole before inserting the inner piston.
Noise reduction O-ring for InkMachines Dragonfly X2 tattoo machine, original spare part no. 22, set of 2 pieces. These specialized O-rings are designed to significantly reduce the Dragonfly X2 noise level by dampening vibrations generated by the drive mechanism. Manufactured from high-quality elastomeric material resistant to wear and chemicals used in professional tattoo environments, the O-rings absorb mechanical vibrations and prevent their transmission to the machine body. The result is considerably quieter operation that improves comfort for both artist and client during long tattoo sessions. InkMachines developed these components in response to feedback from professional artists who appreciate a quieter working environment. The Dragonfly X2 is already one of the quietest rotary tattoo machines, and the dampening O-rings complement this quality. The set of 2 O-rings covers the requirement for a complete service. Replacement is recommended when increased noise levels, visible O-ring deformation, or loss of elastic properties is observed. Original InkMachines part with dampening properties specifically calibrated for the Dragonfly X2. Studio comfort is an important factor for artist productivity and client satisfaction. Original InkMachines dampening O-rings contribute to a professional and pleasant working environment. Available on tatuat.ro with fast delivery throughout Romania and Swedish manufacturer authenticity guarantee. These O-rings are among the simplest yet most effective upgrades for improving the day-to-day tattooing experience in any professional studio.
Frequently Asked Questions How much do the O-rings reduce Dragonfly X2 noise? O-rings no. 22 significantly reduce noise levels by absorbing mechanical vibrations transmitted from the drive mechanism to the machine body. The difference is immediately perceptible after installation. The Dragonfly X2 equipped with new O-rings operates considerably quieter, creating a more pleasant working environment. How often should the O-rings be replaced? Dampening O-rings are wear parts that lose their elastic properties over time. For intensive professional use, we recommend checking every 3-6 months and replacing when deformation, material hardening, or increased noise levels are observed. The low price makes preventive replacement very accessible. Are the O-rings autoclave resistant? Original InkMachines O-rings no. 22 are manufactured from elastomeric material resistant to chemicals used in the tattoo environment. However, repeated exposure to high autoclave temperatures can accelerate material degradation. Check O-ring condition more frequently if you subject them to high-temperature sterilization. How much does the O-ring set no. 22 cost? The set of 2 InkMachines O-rings no. 22 is available at approximately 1.50 EUR. The extremely accessible cost makes regular replacement an insignificant investment compared to the benefit of quiet machine operation. We recommend purchasing multiple spare sets. Can I use generic O-rings instead of originals? We do not recommend generic O-rings because the material and dimensions are specifically calibrated for the Dragonfly X2. O-rings with different hardness will not dampen vibrations correctly - too soft wears quickly, too hard does not absorb vibrations efficiently. The price difference is minimal but the performance difference can be significant. Do the O-rings affect machine performance? The O-rings do not affect the machine's mechanical performance, only noise and vibration levels. They function as passive dampeners that absorb vibration energy without interfering with the needle movement mechanism. Tattooing performance remains identical, but usage comfort is significantly improved. How do I install the dampening O-rings? Installing O-rings no. 22 is a simple operation involving positioning them in the dedicated slots in the Dragonfly X2 machine. No special tools are required and it can be done in a few minutes. Ensure the O-rings are correctly positioned and not twisted or pinched before reassembling the machine. Do the O-rings come in different durometers? Original InkMachines O-rings no. 22 have a specific durometer calibrated for optimal vibration dampening of the Dragonfly X2. InkMachines does not offer variants with different durometers because the selected one was determined as optimal through extensive testing. Any modification would compromise the balance between dampening and durability. Does the machine work without the dampening O-rings? Yes, the Dragonfly X2 machine works without the dampening O-rings, but at a higher noise and vibration level. We do not recommend prolonged use without O-rings because unabsorbed vibrations can accelerate wear on other components and cause premature hand fatigue for the artist. What other noise reduction methods exist for the Dragonfly X2? In addition to O-rings no. 22, keeping all components in good condition contributes to quiet operation: new springs, unworn bearing balls, optimal piston condition, and regular lubrication. The InkMachines Dragonfly X2 is designed to operate quietly when all components are in optimal condition.
